Hello, What's the bird version are you using ? The Bird version 3 is in alpha 0, isn't production usable yet. If you like to test, you can download it on https://bird.network.cz/?download Best regards, Ailton NIC.br/IX.br Brasil Internet Exchange Em 19/04/2023 02:19, saifullah@fiberathome.net escreveu:

Hi

CPU MHz: 2494.140. I found the BIRD is using different CPU at different time and it’s crossing 100% utilization using command “htop”. It’s happening when I am trying to establish a neighbor where prefix count is more than 106K. I found that BIRD3 support multi-core. Is there any way to install BIRD 3?

Thanks & Regards

Abu Nasar Md. Saifullah

*From:* Darshan Kowlaser <darshan@darshankowlaser.com> *Sent:* Tuesday, April 18, 2023 11:00 PM *To:* saifullah@fiberathome.net *Subject:* Re: BIRD is taking too much time to converge 106362 prefixes from a non-client iBGP neighbor

Hi

Something to consider is that BGP on BIRD runs on a single core. If you slow clock speed you are going to run into issues? What is the CPU utilization while the BIRD daemon stopped?

On Tue, Apr 18, 2023 at 6:18 PM <saifullah@fiberathome.net <mailto:saifullah@fiberathome.net>> wrote:

Hi Dear,

Thank you for your feedback. The server I am using of 16 VCPU with 2 threads per CPU and 16 GB RAM. I found that CPU utilizations is crossing 100% in a CPU. Any way to install and configure BIRD so that it uses all CPU simultaneously?

Thanks & Regards Abu Nasar Md. Saifullah

-----Original Message----- From: Ondrej Zajicek <santiago@crfreenet.org <mailto:santiago@crfreenet.org>> Sent: Monday, April 17, 2023 6:17 PM To: saifullah@fiberathome.net <mailto:saifullah@fiberathome.net> Cc: bird-users@network.cz <mailto:bird-users@network.cz> Subject: Re: BIRD is taking too much time to converge 106362 prefixes from a non-client iBGP neighbor

On Thu, Apr 13, 2023 at 11:47:12PM +0600, saifullah@fiberathome.net <mailto:saifullah@fiberathome.net> wrote: > Hi, > > Thanks for your feedback. The topology is BIRD is connected with total > 8 neighbors (1 is non-client and 7 are in client mode) for my setup. > The non-client neighbor is actually a high end central RR router which > advertise about 106k prefixes to BIRD and with other 7 client, the > prefix count is below 100. > > 1. During that time, I have checked and found that CPU load was normal. > 2. I also checking prefix count using command "show protocols all > <non_client_neighbor>" and found prefixes were increasing gradually.

Hi

If CPU was normal (idle), then it is unlikely an issue with BIRD. Prefixes are processed as they arrive, so they are delayed only if BIRD cannot catch up and use 100% CPU (note that it is single-threaded, so you have to check load on individual CPUs and not aggregate load, like is default in 'top'). Perhaps the other side send prefixes slowly?

-- Elen sila lumenn' omentielvo

Ondrej 'Santiago' Zajicek (email: santiago@crfreenet.org <mailto:santiago@crfreenet.org>) OpenPGP encrypted e-mails preferred (KeyID 0x11DEADC3, wwwkeys.pgp.net <http://wwwkeys.pgp.net>) "To err is human -- to blame it on a computer is even more so."

Connecting our future with light

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- /The content of this email is confidential and intended for the recipient specified in message only. It is strictly forbidden to share any part of this message with any third party, without a written consent of the sender. If you received this message by mistake, please reply to this message and follow with its deletion, so that we can ensure such a mistake does not occur in the future. / ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- *House # 7/B, Road # 13, Gulshan-1, Dhaka-1212, Phone: +880 2 8814615-6, 8814868 Email: info@fiberathome.net, Website: https://www.fiberathome.net/*